![add diode in parallel with the collector and emitter of the transistor | Arduino, Transistors, Microcontrollers add diode in parallel with the collector and emitter of the transistor | Arduino, Transistors, Microcontrollers](https://i.pinimg.com/originals/33/27/6e/33276e687e0d24db599b88661e9b9d2d.png)
add diode in parallel with the collector and emitter of the transistor | Arduino, Transistors, Microcontrollers
![How to protect a microcontroller analog pin from continuous overvoltage? - Electrical Engineering Stack Exchange How to protect a microcontroller analog pin from continuous overvoltage? - Electrical Engineering Stack Exchange](https://i.stack.imgur.com/C8rY5.png)
How to protect a microcontroller analog pin from continuous overvoltage? - Electrical Engineering Stack Exchange
![Dumb question, but can you add a pull-down resistor to a voltage clamp diode as shown in the picture below? D3 is a pin going into the microcontroller, and the pull-down is Dumb question, but can you add a pull-down resistor to a voltage clamp diode as shown in the picture below? D3 is a pin going into the microcontroller, and the pull-down is](https://i.redd.it/mf8dy8nav9j31.png)
Dumb question, but can you add a pull-down resistor to a voltage clamp diode as shown in the picture below? D3 is a pin going into the microcontroller, and the pull-down is
![12V to 5V converter | Step down DC regulator in many ways to do | Electronic circuit projects, Converter, Electronics basics 12V to 5V converter | Step down DC regulator in many ways to do | Electronic circuit projects, Converter, Electronics basics](https://i.pinimg.com/736x/44/0d/0f/440d0fb3c574274490b1a65c6ef85890.jpg)
12V to 5V converter | Step down DC regulator in many ways to do | Electronic circuit projects, Converter, Electronics basics
![A 5.1-volt zener diode clamps the output of the smoke alarm to about 5 volts, helping to protect the input of the microcontroller. You may also wish to add extra protection in A 5.1-volt zener diode clamps the output of the smoke alarm to about 5 volts, helping to protect the input of the microcontroller. You may also wish to add extra protection in](https://www.accessengineeringlibrary.com/binary/mheaeworks/4c60842195f3ac7d/c45ef01dee79814d3849704339a26097f0cfcc9418a5d02ddc287cfecfeefe7b/48x05.png)
A 5.1-volt zener diode clamps the output of the smoke alarm to about 5 volts, helping to protect the input of the microcontroller. You may also wish to add extra protection in
![Connecting Light Emitting Diodes (LED) to a PIC Microcontroller - XC8 | Student CompanionStudent Companion Connecting Light Emitting Diodes (LED) to a PIC Microcontroller - XC8 | Student CompanionStudent Companion](https://www.studentcompanion.co.za/wp-content/uploads/2015/07/LED.jpg)
Connecting Light Emitting Diodes (LED) to a PIC Microcontroller - XC8 | Student CompanionStudent Companion
TMS320F28388D: power sequence for 28388 - C2000 microcontrollers forum - C2000™︎ microcontrollers - TI E2E support forums
![Connecting Light Emitting Diodes (LED) to a PIC Microcontroller - XC8 | Student CompanionStudent Companion Connecting Light Emitting Diodes (LED) to a PIC Microcontroller - XC8 | Student CompanionStudent Companion](https://www.studentcompanion.co.za/wp-content/uploads/2014/03/LED-connected-in-current-sinking-mode.jpg)
Connecting Light Emitting Diodes (LED) to a PIC Microcontroller - XC8 | Student CompanionStudent Companion
![Using a piezo to wake 3.3V microcontroller when there's vibration - General Electronics - Arduino Forum Using a piezo to wake 3.3V microcontroller when there's vibration - General Electronics - Arduino Forum](https://aws1.discourse-cdn.com/arduino/original/4X/1/e/f/1efc4ace9278217a21cbecf563bcfad849e2b9e8.jpeg)